Maker Mask
  • Home
    • CDC Masks
  • Shop
    • The Radius
    • Replacement Filters
  • Makers Zone
    • Download >
      • Terms and Conditions
      • Disclaimer
    • MM Member Forum
    • Radius >
      • Care and Use
    • Respirator
    • Rapid
  • About Us
    • Maker Team
    • Senior Advisors
    • Contact
    • Our Partners
    • Newsroom >
      • Media Assets
      • Press Releases
      • News Coverage
    • MM Connect Blog
    • Donate
Picture
Picture
When you need a serious mask. 

For Humanity, Not Profit

We're Live!!
​Pre-order your injection molded Radius Mask on Indiegogo today! 

BUY NOW!
Picture

Picture


Picture
Picture
Highlights
Features and Benefits:
· 3 uniformly sized filters
· Softer plastic for a more comfortable fit
· Easier breathability
· Same filter quality, but with fewer pieces to print and assemble!

​
All parts are 3D printable within 1.5 Hours, and HEPA filter is replaceable.
This version is intended for individuals with deep knowledge of 3D printing.

RADIUS MASK DISCLAIMER:
This design is currently in NIH review.


Join & Download Spec

Picture
Picture
Highlights
Features and Benefits:
· 2 oversized sized inhale filters with internal valves

· Front expel filter with valve
· Softer plastic for a more comfortable fit
· Easier breathability and fit
· First Responder edition with highest level of filtration

​
All parts are 3D printable within 3 Hours, and HEPA filter is replaceable.
This version is intended for individuals with moderate knowledge of 3D printing.

RESPIRATOR MASK DISCLAIMER:

 This prototype model is pending NIH assessment for community use. The results of this process may result in modification.
~Prior model has NIH Approval.~

​
Join & Download Spec

Picture
Picture
Highlights
Features and Benefits:
· 1 oversized solo central filter

· Softer plastic for a more comfortable fit
· Easier breathability and fit
· Simple edition with good filtration and easy to print

​
All parts are 3D printable within 1.5 Hours, and HEPA filter is replaceable.
This version is intended for individuals with mild knowledge of 3D printing.

RAPID MASK DISCLAIMER:

 This prototype model is pending NIH assessment for community use. The results of this process may result in modification.

Join & Download Spec
Picture
The Maker Mask Respirator has been approved by the NIH for all general community applications:  This approval applies for use outside of the direct healthcare setting and benefits critical front-line essential service providers including:  Police/Law Enforcement, Fire and Rescue and other Emergency Response service providers.  The Maker Mask is also a great option for essential service resources providing our communities with food and other needed supplies:  Grocery, Delivery, Transportation and other supporting services.

NIH Posting
Learn more

We’re Building a Community of 3D Printing Enthusiasts to Fight the COVID-19 Global Crisis

Our goal is to enable people to meet the community needs for respirator-quality masks and other critical medical supplies through 3D printing around the world.
WHO
Humanitarians, People with 3D printers, hobbyists, civic groups, Maker Spaces, universities, schools churches and available willing/government units. Donations to this effort can be made through our Maker Mask/RPrime Donation Center. Donation Center.
WHY
Enabling communities to create necessary goods locally and quickly will lessen the spread of disease, protect more people, reduce burdens on medical facilities/DoD/governments, and give Americans something they can do to be part of the solution to this pandemic, while building and training capability for the future.  
WHAT
The Maker Mask is a respirator style mask created by Rory Larson at the request of several local hospitals in Seattle. 
COST
We are mindful of costs and have tried to limit barriers to participating. Not including electricity or cost of printers and labor - which is all volunteer and donated here in Seattle - the costs of the inputs are low we estimate that the cost of each finished mask to be roughly between $2 and $3 dollars. 

 “Good news!  Seattle Children’s Hospital has a team that has tested and medically endorsed the first set of masks."
Picture
“I am very excited to be the first person to try these 3D printed mask……these 3D printed masks have great potential to be used in non-patient medical contact sectors…it will help solve shortages in Personal Protective Equipment in these unprecedented times!”

​Xuan Qin, PhD, D(ABMM)
Professor, Laboratory Medicine, University of Washington

Division Chief, Microbiology Laboratory
Seattle Children's Hospital

Listen to Dr. Qin's Testimony
Read the endorsement
Picture
Nurses at Seattle Children's Hospital receiving a new bulk shipment of
​Maker Masks and Replaceable HEPA Filters!
​4/4/2020

Maker Mask Evolution


An overview from the Maker Mask leadership team and platform architects on how the product is made and current progress.

The World Needs Maker Mask

1. Medical community reviewed and endorsed Open Source 3D printable mask.
2. Re-usable. Flexibility on filters than can be used and replaced.
3. Buildable with readily available items found at most local hardware stores.
4. Maker Mask can be custom-fit to your face through a simple heating and shaping process – if needed.
5. Patent Pending design by Rory Larson. He is contributing it free of charge and delivering it open source.
6. Funding for the initiative provided by RPrime, a Washington State 501 (c)(3) non-profit.​
Join the Movement

SEATTLE CROWD-SOURCING “FRANCHISE” PILOT

Seattle is all about scale and entrepreneurship. In Seattle, a team consisting of Rory and Garr Larson, and Jonathan Roberts are starting a Maker Mask community-based production run. Our vision is to scale this production by creating “Small Batch Production Franchises.”
As of March 29, 2020 we have accumulated 40 3D printers and supplies to create up to 20K masks. We believe that we could be running 24 hours a day and produce 300 masks per day with this effort. Through Small Batch Production, we can create all the back-up materials and support infrastructure necessary for your group or organization to create your own Small Batch Production facility. 
We intend to share their best practices and hopefully start a movement in the humanitarian, hobbyist, civic communities. We can show you how.
Contact The Team
Picture
Picture

MEET THE TEAM


Jonathan Roberts

Picture

RELATIONSHIPS LEAD

Read BIO

Garr Larson

Picture

TEAM LEAD

Read BIO

Rory Larson

Picture

CHIEF ARCHITECT

Read BIO

Taylor Odegard

Picture

DIGITAL LOGISTICS

Read BIO

Picture
To Support Maker Mask Covid-19 Initiative
Donate
Home
Team
Elements
Contact
Privacy Policy
Picture
Maker Mask Credo: Enabling communities to create necessary goods locally and quickly will lessen the spread of disease, protect more people, reduce burdens on medical facilities/DoD/governments, and give Americans something they can do to be part of the solution to this pandemic, while building and training capability for the future.  

​www.makermask.com     Copyright 2020. All Rights Reserved

General Inquiries
info@makermask.com
Media Inquiries
pr@makermask.com
​

(866) 323-MASK (6275)
2001 6th Ave, Suite 1610
Seattle, WA 98121
  • Home
    • CDC Masks
  • Shop
    • The Radius
    • Replacement Filters
  • Makers Zone
    • Download >
      • Terms and Conditions
      • Disclaimer
    • MM Member Forum
    • Radius >
      • Care and Use
    • Respirator
    • Rapid
  • About Us
    • Maker Team
    • Senior Advisors
    • Contact
    • Our Partners
    • Newsroom >
      • Media Assets
      • Press Releases
      • News Coverage
    • MM Connect Blog
    • Donate